// Walkie talkie case


// Set units
@settings(defaultLengthUnit = in)


// Import constants and Zoo logo
import width, height, chamferLength, offset, screenWidth, screenHeight, screenYPosition, screenDepth, speakerBoxWidth, speakerBoxHeight, squareHoleSideLength, caseTolerance from "globals.kcl"
import zLogo, oLogo, oLogo2 from "zoo-logo.kcl"

plane = offsetPlane("XZ", offset = 1)

fn screenHole(sketchStart) {
  sketch006 = startSketchOn(sketchStart)
    |> startProfileAt([-screenWidth / 2, screenYPosition], %)
    |> xLine(screenWidth, %)
    |> yLine(-screenHeight, %)
    |> xLine(-screenWidth, %)
    |> line(endAbsolute = [profileStartX(%), profileStartY(%)])
    |> close()
  return sketch006
}

fn squareHolePattern(plane, x, y) {
  fn transformX(i) {
    return { translate = [.125 * i, 0] }
  }
  fn transformY(i) {
    return { translate = [0, -.125 * i] }
  }
  squareHolePatternSketch = startSketchOn(plane)
    |> startProfileAt([-x, -y], %)
    |> line(end = [squareHoleSideLength / 2, 0])
    |> line(end = [0, -squareHoleSideLength / 2])
    |> line(end = [-squareHoleSideLength / 2, 0])
    |> close()
    |> patternTransform2d(instances = 13, transform = transformX)
    |> patternTransform2d(instances = 11, transform = transformY)
  return squareHolePatternSketch
}
sketch005 = startSketchOn(offsetPlane("XZ", offset = 1))
  |> startProfileAt([
       -width / 2 + offset + caseTolerance,
       height / 2 - (chamferLength + (offset + caseTolerance) / 2 * cos(toRadians(45)))
     ], %)
  |> angledLineToY({
       angle = 45,
       to = height / 2 - (offset + caseTolerance)
     }, %)
  |> line(endAbsolute = [
       width / 2 - (chamferLength + (offset + caseTolerance) / 2 * cos(toRadians(45))),
       height / 2 - (offset + caseTolerance)
     ])
  |> angledLineToX({
       angle = -45,
       to = width / 2 - (offset + caseTolerance)
     }, %)
  |> line(endAbsolute = [
       width / 2 - (offset + caseTolerance),
       -(height / 2 - (chamferLength + (offset + caseTolerance) / 2 * cos(toRadians(45))))
     ])
  |> angledLineToY({
       angle = -135,
       to = -height / 2 + offset + caseTolerance
     }, %)
  |> line(endAbsolute = [
       -(width / 2 - (chamferLength + (offset + caseTolerance) / 2 * cos(toRadians(45)))),
       -height / 2 + offset + caseTolerance
     ])
  |> angledLineToX({
       angle = -225,
       to = -width / 2 + offset + caseTolerance
     }, %)
  |> close()
  |> hole(screenHole(plane), %)
  |> hole(squareHolePattern(plane, .75, .125), %)
  |> hole(zLogo(plane, [-.30, -1.825], .20), %)
  |> hole(oLogo(plane, [-.075, -1.825], .20), %)
  |> hole(oLogo2(plane, [-.075, -1.825], .20), %)
  |> hole(oLogo(plane, [.175, -1.825], .20), %)
  |> hole(oLogo2(plane, [.175, -1.825], .20), %)

extrude(sketch005, length = -0.0625)
  |> appearance(color = '#D0FF01', metalness = 0, roughness = 50)