ffbe20b586
Previous: ``` startProfileAt([x, y], %) startProfileAt([x, y], sketch001) ``` New: ``` startProfile(%, at = [x, y]) startProfile(sketch001, at = [x, y]) ```
53 lines
2.4 KiB
Plaintext
53 lines
2.4 KiB
Plaintext
d_wrist_circumference = [22.8, 10.7, 16.4, 18.5]
|
|
width = d_wrist_circumference[0] + d_wrist_circumference[1] + d_wrist_circumference[2] + d_wrist_circumference[3]
|
|
length = 120.0
|
|
hand_thickness = 24.0
|
|
corner_radius = 5.0
|
|
|
|
// At first I thought this was going to be symmetric,
|
|
// but I measured intentionally to not be symmetric,
|
|
// because your wrist isn't a perfect cylindrical surface
|
|
brace_base = startSketchOn(XY)
|
|
|> startProfile(at = [corner_radius, 0])
|
|
|> line(end = [width - corner_radius, 0.0])
|
|
|> tangentialArc(end = [corner_radius, corner_radius])
|
|
|> yLine(length = 25.0 - corner_radius)
|
|
|> tangentialArc(end = [-corner_radius, corner_radius])
|
|
|> xLine(length = -(d_wrist_circumference[0] - (corner_radius * 2)))
|
|
|> tangentialArc(end = [-corner_radius, corner_radius])
|
|
|> yLine(length = length - 25.0 - 23.0 - (corner_radius * 2))
|
|
|> tangentialArc(end = [corner_radius, corner_radius])
|
|
|> xLine(length = 15.0 - (corner_radius * 2))
|
|
|> tangentialArc(end = [corner_radius, corner_radius])
|
|
|> yLine(length = 23.0 - corner_radius)
|
|
|> tangentialArc(end = [-corner_radius, corner_radius])
|
|
|> xLine(length = -(hand_thickness + 15.0 + 15.0 - (corner_radius * 2)))
|
|
|> tangentialArc(end = [-corner_radius, -corner_radius])
|
|
|> yLine(length = -(23.0 - corner_radius))
|
|
|> tangentialArc(end = [corner_radius, -corner_radius])
|
|
|> xLine(length = 15.0 - (corner_radius * 2))
|
|
|> tangentialArc(end = [corner_radius, -corner_radius])
|
|
|> yLine(length = -(length - 25.0 - 23.0 - (corner_radius * 2)))
|
|
|> tangentialArc(end = [-corner_radius, -corner_radius])
|
|
|> xLine(length = -(d_wrist_circumference[1] + d_wrist_circumference[2] + d_wrist_circumference[3] - hand_thickness - corner_radius))
|
|
|> tangentialArc(end = [-corner_radius, -corner_radius])
|
|
|> yLine(length = -(25.0 - corner_radius))
|
|
|> tangentialArc(end = [corner_radius, -corner_radius])
|
|
|> close(%)
|
|
|
|
inner = startSketchOn(XY)
|
|
|> startProfile(at = [0, 0])
|
|
|> xLine(length = 1.0)
|
|
|> tangentialArc(end = [corner_radius, corner_radius])
|
|
|> yLine(length = 25.0 - (corner_radius * 2))
|
|
|> tangentialArc(end = [-corner_radius, corner_radius])
|
|
|> xLine(length = -1.0)
|
|
|> tangentialArc(end = [-corner_radius, -corner_radius])
|
|
|> yLine(length = -(25.0 - (corner_radius * 2)))
|
|
|> tangentialArc(end = [corner_radius, -corner_radius])
|
|
|> close(%)
|
|
|
|
final = brace_base
|
|
|> hole(inner, %)
|
|
|> extrude(length = 3.0)
|